Understanding Plumbing Basics for Bathtub Installation
Call TodayEveryone will have their own unique way of thinking about How to Install a Bathtub Yourself.
Mounting a bath tub isn't specifically rocket science, but it does need solid plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bath tub with a new one is additionally a reasonably challenging task. If the old bathtub is readily available, the project can move easily; if you have to open up a wall surface to get rid of the old bathtub and place the brand-new bath tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub and set in the new one. Make certain you have actually qualified yourself for the work and also fit trying it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Possibilities are you may need a specialist plumber to make tube connections.
This write-up will help you install a new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and do not require to change the plan of your previous supply of water pipelines.
Your devices as well as product checklist ought to make up the following:
Planning for the Installation
To start with, the supporting frame supplied with the bath must be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to stop stress on the tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its last setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you must do is disconnect the supply of water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be rather bothersome because of the limited gain access to that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will come from the pipelines. As soon as the supply pipes have actually been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any old securing compound.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Utilizing the two wooden boards under its feet, put the tub in the required position. The wood boards are valuable in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the spirit level and changing the feet on the tub until the spirit level reads degree.
To mount faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Activate the supply of water and also examine all joints and also brand-new pipework for leaks and also tighten them if needed. Fill the bathtub as well as likewise inspect the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bathtub must wait till the tub has been used at the very least once as this will certainly settle it into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers are in area between the faucet as well as the sink. Safeguard the faucet in position with the manufacturer given backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be connected to the tap ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to crack an inflexible seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing complications with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Remember to always fill the bath tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealant can fracture rather very early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that page on How to Install a Bathtub while doing a lookup on the internet. Kindly take the time to promote this blog if you enjoyed reading it. I treasure reading our article about How to Install a Bathtub Yourself.
Plumber on standby. Call!