Knowing Plumbing Basics is Essential When Installing a Bathtub
Call TodayThe content following next about How to Install a Bathtub Yourself is particularly compelling. You should keep reading.
Setting up a bathtub isn't precisely rocket science, yet it does call for solid plumbing, carpentry, and often, tiling skills. Changing an old tub with a new one is also a reasonably challenging project. If the old tub is easily accessible, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and place the new bath tub, the task is a lot harder. In either case, the project is within a house handyman's skills, although you will need a helper to vacate the old tub and embeded in the brand-new one. See to it you have qualified yourself for the task and are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed task, it is better to take into consideration using one prior to you start. Possibilities are you may need an expert plumber to make tube links.
This write-up will aid you set up a new bathtub in your restroom if you have actually currently purchased a new tub as well as don't require to transform the arrangement of your previous supply of water pipes.
Your devices and also material list need to make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of removing the existing faucets can be quite bothersome due to the restricted gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Prior to going on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and also the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the faucet and also the sink. Protect the tap in position with the manufacturer given backnut. When the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The previous kind should be connected to the faucet finishes initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, position the bathtub in the required position. The wooden boards are useful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub till the level reads level.
To set up faucets, fit all-time low of the furthest adaptable tap port to the proper supply pipe by making a compression join; then do the same for the other tap.
Activate the water system and also examine all joints and also new pipework for leaks as well as tighten them if needed. Load the tub and likewise inspect the overflow outlet and the typical electrical outlet for leaks.
Ultimately, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bathtub must wait up until the bathtub has been made use of at the very least when as this will certainly resolve it into its last placement.
Preparing for the Setup
To start with, the sustaining framework provided with the bathroom should be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to avoid strain on the bathtub.
Fit the flexible tap connectors to the bottom of both taps making use of 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath must now prepare to be suited its last position.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack an inflexible seal, triggering the water to pass through the wall surface between the bath and also the tiling, resulting in complications with moisture and feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your components and also fittings. They are sold in tubes and also cartridges, and can securing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched paper or soft rope. Remember to always load the bathtub with water prior to securing, to permit the motion experienced when the tub remains in usage. The sealant can crack rather early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly offered on the market. It is advisable to fit the tiles utilizing water-resistant or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for taking a few minutes to browse our post. Feel free to take the time to distribute this blog entry if you enjoyed reading it. I praise you for your time. Kindly come by our website back soon.
Search no more; expert plumbers.